VTech Riding Toy 91 002768 007 User Manual

User’s Manual  
TM  
Sit-to-Race Smart Wheels  
© 2012 VTech  
Printed in China  
US  
 
91-002768-007  
INTRODUCTION  
Thank you for purchasing the VTech® Sit-to-Race Smart WheelsTM  
learning toy!  
Rock, ride and learn with the Sit-to-Race SmartWheelsTM by VTech®!  
This ride-on toy grows with your child and helps them learn numbers,  
gross motor skills, pretend play, and more! For the younger child, the  
dashboard activity panel can be played with on the floor and features a  
horn button, twisting knob, two handle bars, and four number buttons.  
As your child grows, they can sit on the bike, which can be used as a  
rocker or as a ride-on that can be pushed by parents.  
FouR nuMbER buTTons  
hAnDLE  
bARs  
MoDE sELECToR  
TwisT Knob  
voLuME ConTRoL swiTCh  
hoRn  
buTTon  
RoCKER bECoMEs  
oPTionAL PAREnT hAnDLE  
 
INCLUDED IN THIS PACKAGE  
one electronic dashboard activity panel – Two handle bars  
one body  
– Rocker/parent handle pieces  
– Four wheels, two axles, four cylinders, fasteners and spindles  
one user’s manual  
 
WARNING:  
All packing materials, such as tape, plastic sheets, packaging  
locks and tags are not part of this toy, and should be discarded  
for your child’s safety.  
ATTENTION  
Pour la sécurité de votre enfant, débarrassez-vous de tous  
les produits d’emballage tels que rubans adhésifs, feuilles de  
plastique, attaches et étiquettes. Ils ne font pas partie du jouet.  
NOTE:  
Please keep this instruction manual as it contains important  
information.  
INSTRUCTIONS  
BATTERY INSTALLATION  
1. Make sure the unit is turned OFF.  
2. Locate the battery cover on the bottom  
of the dashboard activity panel. use a  
screwdriver to loosen the screw.  
3. install 2 new ‘AA’ (AM-3/LR6)  
batteries following the diagram inside  
the battery box. (The use of new  
alkaline batteries is recommended for  
maximum performance.)  
4. Replace the battery cover and tighten  
the screw to secure.  
BATTERY NOTICE  
use new alkaline batteries for maximum performance.  
use only batteries of the same or equivalent type as  
recommended.  
Do not mix different types of batteries: alkaline, standard (carbon-  
 
zinc) or rechargeable (ni-Cd, ni-Mh), or new and used batteries.  
Do not use damaged batteries.  
insert batteries with the correct polarity.  
Do not short-circuit the battery terminals.  
Remove exhausted batteries from the toy.  
Remove batteries during long periods of non-use.  
Do not dispose of batteries in fire.  
Do not charge non-rechargeable batteries.  
Remove rechargeable batteries from the toy before charging (if  
removable).  
Rechargeable batteries are only to be charged under adult  
supervision.  
PRODUCT ASSEmbLy  
CAUTION: with the VTech® Sit-to-Race Smart  
WheelsTM, safety comes first. To ensure your child’s safety, please  
only assemble this product by an adult. This package contains four  
small screws. For your child’s safety, do not let your child play with  
the toy until it is fully assembled. Adult supervision required.  
ASSEMBLY INSTRUCTIONS  
1. To install the four wheels onto the body, first insert an axle through  
one wheel and one yellow cylinder. Please be sure the deeper hole  
in the wheel faces out, and the larger end of the yellow cylinder goes  
inside the body. Maneuver the cylinder until it locks into place.  
 
insert another yellow cylinder and  
one wheel onto the open end of the  
axle. Please be sure the deeper hole  
in the wheel faces out, and the larger  
end of the yellow cylinder goes inside  
the body. Maneuver the cylinder until  
it locks into place.  
Cover with a fastener, with the spindle  
side up and aligned with the hole  
in the axle, then insert the spindle  
through the hole in the axle. Put a  
cover over the fastener, aligning the  
holes in the cover with the holes in the  
fastener. insert two screws into the  
cover and tighten with a screwdriver.  
Repeat this process for the second  
wheel.  
2. To attach the left and right handle  
bars to the dashboard activity panel,  
insert them into the holes on the  
sides. You will hear a loud ‘click’  
sound. This indicates that the handle  
bars are securely fixed into the  
dashboard activity panel.  
 
3. Attach the dashboard activity panel to  
the body by snapping the dashboard  
activity panel onto the body. You  
will hear it click into place. Please  
ensure the dashboard activity panel  
is attached securely to the body.  
4. To assemble the parent handle, first  
insert the handle grip into the middle  
support. Attach each side piece by  
pushing down the locks on the side  
piece and inserting the male parts of  
the handle grip and middle support  
into the corresponding female parts  
of the side piece. You will hear the  
side pieces click into place.  
5. Place the bottom of the parent handle onto the back axle at a  
45-degree angle, then rotate the handle up to connect to the rear  
of the seat. Lock the parent handle in place by tightening the large  
screw.  
 
WARNING!  
Not to be used by children over ꢁꢄ months due to insufficient  
strength. ꢂꢀ pounds max.  
ATTENTION !  
This toy should be operated in a safe area.  
Please ensure young children are supervised by an adult.  
Please ensure your child is positioned correctly on the seat  
when in ride-on or rocker mode.  
This toy should be used with caution to avoid falls or collisions  
that cause injury to your child or others.  
CONvERTINGTHESIT-TO-RACESmART  
WHEELSTM  
1. To convert to rocker mode, press and  
hold the green button on the side of  
the seat, loosen the large screw on  
the handle, then rotate the handle to a  
horizontal position under the body.  
Push the handle into the two locks  
under the front wheels. You will hear  
a click to indicate the parent handle  
is secure and can be used as rocker  
blades.  
 
2. To convert to ride-on mode, squeeze the two locks under the front  
wheels to disconnect the handle. Rotate the handle to a vertical  
position behind the body.  
secure the handle by tightening the  
large screw.  
PLEASE NOTE:  
The handle is designed for parental use only. This product  
should not be used by a child as a push toy.  
3. To remove the handle in ride-on mode, press and hold the green  
button on the seat and unscrew the large screw. Then, move the  
handle to a 45-degree angle and remove it from the axle.  
 
4. To remove the dashboard activity  
panel from the body, turn over the  
body and squeeze the green locks  
inside, under the activity panel.  
Remove the dashboard activity panel  
from the body.  
To avoid injury caused by the lock on  
the neck of the body, please keep the  
body out of your child’s reach when  
playing with the dashboard activity  
panel by itself on the floor.  
PRODUCT FEATURES  
1. MODE SELECTOR  
To turn the unit ON, slide the MODE  
SELECTOR to the LEARNING  
MODE ( ) or the DISCOVERY  
MODE ( ) position. To turn the unit  
OFF, slide the MODE SELECTOR to  
the OFF ( ) position.  
 10  
ꢀ. VOLUME CONTROL SWITCH  
To adjust the volume, slide the  
VOLUMECONTROLSWITCHonthe  
dashboard activity panel to the LOW  
VOLUME ( )or the HIGHVOLUME  
(
) position.  
ꢁ. AUTOMATIC SHUT-OFF  
To preserve battery life, the VTech® Sit-to-Race SmartWheelsTM  
will automatically power-down after approximately 45 seconds  
without input. The unit can be turned on again by pressing any  
button.  
ACTIvITIES  
1. slide the mode selector to the  
learning mode or discovery mode  
position to turn the unit on. You will  
hear a song, a playful phrase and the  
horn sound. The light will flash with  
the sounds.  
2. Press the horn button to hear fun  
horn sounds. The light will flash with  
the sounds.  
 11  
3. Twist the twist knob to hear fun  
engine sounds. The light will flash  
with the sounds.  
4. Press the four number buttons to  
learn numbers, objects and places,  
You’ll also hear sounds and an  
encouraging phrase. The light will  
flash with the sounds.  
5. Rock and ride the bike to hear fun  
sounds and melodies. The light will  
flash with the sounds.  
6. if there is no input to the unit after approximately 8 seconds, you  
will hear a question, which will encourage you to find the correct  
object. After another 8 seconds if there is still no input, you will  
hear a fun sung song or an encouraging phrase. After another  
8 seconds if there is still no input, you will hear a short tune, then  
the unit will automatically power-down.  
 1ꢀ  
MELODY LIST:  
1. i’ve been working on the Railroad  
2. The Glow worm  
3. Three blind Mice  
4. The wheels on the bus  
5. oh, where, oh, where has My Little Dog Gone?  
6. Twinkle, Twinkle, Little star  
7. Three Little Kittens  
8. Polly wolly Doodle  
9. This old Man  
10. Jack & Jill  
11. here we Go ‘Round the Mulberry bush  
12. London bridge  
13. skip to My Lou  
14. hey Diddle Diddle  
15. it’s Raining, it’s Pouring  
16. Pease Porridge hot  
SING-ALONG SONGS  
Song 1  
we’re on our way,  
Riding all around town.  
1-2-3-4,  
wheels go round and round!  
 1ꢁ  
Song ꢀ  
it’s time to ride.  
Let’s ride and play.  
where would you like to ride today?  
Ride to the park?  
Ride to the zoo?  
Ride to the places we like to go to!  
CARE & mAINTENANCE  
1. Keep the unit clean by wiping it with a slightly damp cloth.  
2. Keep the unit out of direct sunlight and away from any direct heat  
source.  
3. Remove the batteries when the unit is not in use for an extended  
period of time.  
4. Do not drop the unit on a hard surface and do not expose the unit  
to moisture or water.  
 1ꢂ  
TROUbLESHOOTING  
if for some reason the program/activity stops working or malfunctions,  
please follow these steps:  
1. Turn the unit OFF.  
2. interrupt the power supply by removing the batteries.  
3. Let the unit stand for a few minutes, then replace the batteries.  
4. Turn the unit ON. The unit should now be ready to play again.  
5. if the product still does not work, replace with an entire set of new  
batteries.  
if the problem persists, please call our Consumer services Department  
at 1-800-521-2010 in the u.s. or 1-877-352-8697 in Canada, and a  
service representative will be happy to help you.  
IMPORTANT NOTE:  
Creating and developing Infant Learning products is accompanied  
by a responsibility that we at VTech® take very seriously. we make  
every effort to ensure the accuracy of the information which forms  
the value of our products. however, errors sometimes can occur.  
it is important for you to know that we stand behind our products  
and encourage you to call our Consumer services Department at  
1-800-521-2010 in the u.s., or 1-877-352-8697 in Canada with  
any problems and/or suggestions that you might have. A service  
representative will be happy to help you.  
 1ꢃ  
NOTE:  
This equipment has been tested and found to comply with the limits for  
a Class b digital device, pursuant to Part 15 of the FCC Rules. These  
limits are designed to provide reasonable protection against harmful  
interference in a residential installation. This equipment generates and  
uses radio frequency energy and if not installed and used in accordance  
with the manufacturer’s instructions, may cause interference to radio  
communications. however, there is no guarantee that interference  
will not occur in a particular installation. if this equipment does cause  
interference with radio or television reception, which can be determined  
by turning the equipment on and off, the user is encouraged to try to  
correct the interference by one or more of the following measures:  
Reorient the receiving antenna.  
increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that  
to which the receiver is connected.  
Consult the dealer or an experienced radio/Tv technician for  
help.  
Caution: changes or modifications not expressly approved by the party  
responsible for compliance could void the user’s authority to operate  
the equipment.  
 1ꢄ  
The left handle bar  
The right handle bar  
PLEASE NOTE:  
Please assemble the product according to the above  
image.  
Please be sure the handle bars are correctly attached  
to the dashboard activity panel.The handle bars should  
not be removable once attached.  
91-002804-000  
80-138600-001-001 HANDLE BAR SHEET  
P/N: 91-002804-000  
COLOR: B/W  
SIZE:101X127MM  
 

THORENS Turntable TD 2010 User Manual
Toshiba TV DVD Combo MD13N1 User Manual
Transcend Information Camera Accessories 2GSDM80 User Manual
TrekStor MP3 Player iBeat 115 User Manual
Tripp Lite Mouse IN3010KB User Manual
Tripp Lite Switch B064 032 04 IPG User Manual
Tunturi Exercise Bike E504 User Manual
Turbosound Speaker TSB 212 User Manual
Verilux Electric Shaver CWST2RB User Manual
ViewSonic Car Video System VS15560 User Manual